3/4" BSF tap drill size
The tap drill for 3/4" BSF (12 TPI) is 17 mm, which gives about 76% of full thread. There’s no single standard chart size, so this is worked out from the thread profile for 75%.
Open in the full tap drill finder
Tap drill by thread percentage
75% is the usual workshop figure. Less thread is easier to tap; more adds little strength.
| Thread % | Ideal drill | Nearest metric drill | Nearest imperial drill |
|---|---|---|---|
| 60% | 17.424 mm 0.6860" | 17.5 mm (57%) | 11/16" 0.6875" (59%) |
| 65% | 17.288 mm 0.6806" | 17.25 mm (66%) | 11/16" 0.6875" (59%) |
| 70% | 17.152 mm 0.6753" | 17.25 mm (66%) | 43/64" 0.6719" (73%) |
| 75% | 17.017 mm 0.6700" | 17 mm (76%) | 43/64" 0.6719" (73%) |
| 80% | 16.881 mm 0.6646" | 17 mm (76%) | 43/64" 0.6719" (73%) |
About this size
BSF uses the same 55° Whitworth form as BSW but with a finer pitch. It was the standard steel-bolt thread on British vehicles and machine tools until Unified and metric threads took over.
- For stainless steel, duplex and other tough materials, go to about 65% thread: a 17.25 mm drill gives 66%. For mild steel, brass and cast iron the 17 mm is fine.
- For a blind hole with 1.5 × D thread engagement (28.6 mm), drill about 37 mm deep. That leaves room for the 3–4 tapered lead threads on a second or plug tap. In steel, 1 × D engagement is usually enough; in aluminium or cast iron allow 1.5–2 × D.
Clearance holes for 3/4" BSF
| Fit | Drill |
|---|---|
| Close | 25/32" (19.84 mm) |
| Medium (normal) | 13/16" (20.64 mm) |
| Free (loose) | 7/8" (22.22 mm) |
Worked out with our own rule, not taken from a standards table: close = the larger of D + 4% and D + 0.2 mm, medium = the larger of D + 8% and D + 0.4 mm, free = the larger of D + 15% and D + 0.75 mm, each rounded up to the next 1/64". Check against your drawing where the fit matters.
3/4" BSF thread data
| Designation | 3/4" BSF (12 TPI) |
|---|---|
| Standard | BS 84 Whitworth form (55°) |
| Pitch | 12 TPI (2.117 mm pitch) |
| Thread angle | 55° |
| Major diameter | 0.750" (19.05 mm) |
| Pitch (effective) diameter | 0.697" (17.695 mm) |
| Minor diameter, external | 0.643" (16.339 mm) |
| Minor diameter, internal | 0.643" (16.339 mm) |
| Thread depth (internal) | 1.355 mm |
Basic sizes. Real screws are slightly under and real nuts slightly over these values because of tolerance classes.
Quick calculator
Nearest alternatives
If you don’t have the right drill, these give:
- 16.75 mm drill → about 85% thread
- 17 mm drill → about 76% thread
- 17.25 mm drill → about 66% thread
Threads close in size (not interchangeable – the pitch and/or angle differ):
- 3/4" UNC – 19.05 mm major, 10 TPI (2.54 mm pitch)
- 3/4" UNF – 19.05 mm major, 16 TPI (1.587 mm pitch)
- 3/4" BSW – 19.05 mm major, 10 TPI (2.54 mm pitch)
- M20 – 20 mm major, 2.5 mm pitch (10.2 TPI equivalent)
- M20 × 1.5 – 20 mm major, 1.5 mm pitch (16.9 TPI equivalent)
Questions
What size drill for a 3/4" BSF tap?
The tap drill for 3/4" BSF (12 TPI) is 17 mm, which gives about 76% of full thread. There’s no single standard chart size, so this is worked out from the thread profile for 75%.
What size clearance hole for 3/4" BSF?
For a 3/4" BSF screw or bolt, drill 25/32" for a close fit, 13/16" for a medium (normal) fit or 7/8" for a free fit. These come from our stated rule, not a standards table.
What is the pitch of 3/4" BSF?
3/4" BSF (12 TPI) has a 12 TPI (2.117 mm pitch), a 55° thread angle and a 19.05 mm major diameter.
Sources: Profile per BS 84 (55° Whitworth). Threads per inch checked 25/10/2026 against published BSW size tables. There is no single standard tapping chart, so the drill is worked out from the profile. Values are for reference only – check your tap maker’s chart. See the disclaimer.
Spotted a mistake? Report an error.