9/16" BSW tap drill size
The tap drill for 9/16" BSW (12 TPI) is 12.3 mm, which gives about 73% of full thread. There’s no single standard chart size, so this is worked out from the thread profile for 75%.
Open in the full tap drill finder
Tap drill by thread percentage
75% is the usual workshop figure. Less thread is easier to tap; more adds little strength.
| Thread % | Ideal drill | Nearest metric drill | Nearest imperial drill |
|---|---|---|---|
| 60% | 12.661 mm 0.4985" | 12.7 mm (59%) | 1/2" 0.5000" (59%) |
| 65% | 12.526 mm 0.4931" | 12.5 mm (66%) | 1/2" 0.5000" (59%) |
| 70% | 12.39 mm 0.4878" | 12.4 mm (70%) | 31/64" 0.4844" (73%) |
| 75% | 12.254 mm 0.4825" | 12.3 mm (73%) | 31/64" 0.4844" (73%) |
| 80% | 12.119 mm 0.4771" | 12.1 mm (81%) | 31/64" 0.4844" (73%) |
About this size
BSW (Whitworth) has a 55° thread with rounded crests and roots. You will mostly meet it on older British machines and in restoration work. The rounded form means a Whitworth tap gives a slightly stronger root than a 60° thread of the same pitch.
- For stainless steel, duplex and other tough materials, go to about 65% thread: a 12.5 mm drill gives 66%. For mild steel, brass and cast iron the 12.3 mm is fine.
- For a blind hole with 1.5 × D thread engagement (21.4 mm), drill about 29.9 mm deep. That leaves room for the 3–4 tapered lead threads on a second or plug tap. In steel, 1 × D engagement is usually enough; in aluminium or cast iron allow 1.5–2 × D.
Clearance holes for 9/16" BSW
| Fit | Drill |
|---|---|
| Close | 19/32" (15.08 mm) |
| Medium (normal) | 39/64" (15.48 mm) |
| Free (loose) | 21/32" (16.67 mm) |
Worked out with our own rule, not taken from a standards table: close = the larger of D + 4% and D + 0.2 mm, medium = the larger of D + 8% and D + 0.4 mm, free = the larger of D + 15% and D + 0.75 mm, each rounded up to the next 1/64". Check against your drawing where the fit matters.
9/16" BSW thread data
| Designation | 9/16" BSW (12 TPI) |
|---|---|
| Standard | BS 84 Whitworth form (55°) |
| Pitch | 12 TPI (2.117 mm pitch) |
| Thread angle | 55° |
| Major diameter | 0.563" (14.287 mm) |
| Pitch (effective) diameter | 0.509" (12.932 mm) |
| Minor diameter, external | 0.456" (11.577 mm) |
| Minor diameter, internal | 0.456" (11.577 mm) |
| Thread depth (internal) | 1.355 mm |
Basic sizes. Real screws are slightly under and real nuts slightly over these values because of tolerance classes.
Quick calculator
Nearest alternatives
If you don’t have the right drill, these give:
- 12.2 mm drill → about 77% thread
- 12.3 mm drill → about 73% thread
- 12.4 mm drill → about 70% thread
Threads close in size (not interchangeable – the pitch and/or angle differ):
- 9/16" UNC – 14.29 mm major, 12 TPI (2.117 mm pitch)
- 9/16" UNF – 14.29 mm major, 18 TPI (1.411 mm pitch)
- 9/16" BSF – 14.29 mm major, 16 TPI (1.587 mm pitch)
- M14 – 14 mm major, 2 mm pitch (12.7 TPI equivalent)
- M14 × 1.5 – 14 mm major, 1.5 mm pitch (16.9 TPI equivalent)
Questions
What size drill for a 9/16" BSW tap?
The tap drill for 9/16" BSW (12 TPI) is 12.3 mm, which gives about 73% of full thread. There’s no single standard chart size, so this is worked out from the thread profile for 75%.
What size clearance hole for 9/16" BSW?
For a 9/16" BSW screw or bolt, drill 19/32" for a close fit, 39/64" for a medium (normal) fit or 21/32" for a free fit. These come from our stated rule, not a standards table.
What is the pitch of 9/16" BSW?
9/16" BSW (12 TPI) has a 12 TPI (2.117 mm pitch), a 55° thread angle and a 14.287 mm major diameter.
Sources: Profile per BS 84 (55° Whitworth). Threads per inch checked 25/10/2026 against published BSW size tables. There is no single standard tapping chart, so the drill is worked out from the profile. Values are for reference only – check your tap maker’s chart. See the disclaimer.
Spotted a mistake? Report an error.