M4 tap drill size
The tap drill for M4×0.7 is 3.3 mm. That’s the standard chart size and gives about 77% of full thread.
Open in the full tap drill finder
Tap drill by thread percentage
75% is the usual workshop figure. Less thread is easier to tap; more adds little strength.
| Thread % | Ideal drill | Nearest metric drill | Nearest imperial drill |
|---|---|---|---|
| 60% | 3.454 mm 0.1360" | 3.5 mm (55%) | #29 0.1360" (60%) |
| 65% | 3.409 mm 0.1342" | 3.4 mm (66%) | #29 0.1360" (60%) |
| 70% | 3.363 mm 0.1324" | 3.4 mm (66%) | #29 0.1360" (60%) |
| 75% | 3.318 mm 0.1306" | 3.3 mm (77%) | #30 0.1285" (81%) |
| 80% | 3.273 mm 0.1288" | 3.3 mm (77%) | #30 0.1285" (81%) |
About this size
ISO metric coarse is the default thread for general engineering in the UK and Europe. If a drawing just says “M10”, it means the coarse pitch.
- For stainless steel, duplex and other tough materials, go to about 65% thread: a 3.4 mm drill gives 66%. For mild steel, brass and cast iron the 3.3 mm is fine.
- For a blind hole with 1.5 × D thread engagement (6 mm), drill about 8.8 mm deep. That leaves room for the 3–4 tapered lead threads on a second or plug tap. In steel, 1 × D engagement is usually enough; in aluminium or cast iron allow 1.5–2 × D.
Clearance holes for M4
| Fit | Drill |
|---|---|
| Close | 4.3 mm (0.169") |
| Medium (normal) | 4.5 mm (0.177") |
| Free (loose) | 4.8 mm (0.189") |
Fine, medium and coarse series from ISO 273. Medium suits most jobs; use fine where parts must locate closely and coarse for quick assembly or coated bolts.
M4 thread data
| Designation | M4×0.7 |
|---|---|
| Standard | ISO 68-1 basic profile, ISO 261/262 series |
| Pitch | 0.7 mm pitch (36.3 TPI equivalent) |
| Thread angle | 60° |
| Major diameter | 4 mm (0.157") |
| Pitch (effective) diameter | 3.545 mm (0.140") |
| Minor diameter, external | 3.141 mm (0.124") |
| Minor diameter, internal | 3.242 mm (0.128") |
| Thread depth (internal) | 0.379 mm |
Basic sizes. Real screws are slightly under and real nuts slightly over these values because of tolerance classes.
Quick calculator
Nearest alternatives
If you don’t have the right drill, these give:
- 3.2 mm drill → about 88% thread
- 3.3 mm drill → about 77% thread
- 3.4 mm drill → about 66% thread
Threads close in size (not interchangeable – the pitch and/or angle differ):
- 3BA – 4.1 mm major, 0.73 mm pitch (34.8 TPI equivalent)
- #8 UNC – 4.17 mm major, 32 TPI (0.794 mm pitch)
- #8 UNF – 4.17 mm major, 36 TPI (0.706 mm pitch)
- 4BA – 3.6 mm major, 0.66 mm pitch (38.5 TPI equivalent)
Questions
What size drill for a M4 tap?
The tap drill for M4×0.7 is 3.3 mm. That’s the standard chart size and gives about 77% of full thread.
What size clearance hole for M4?
For a M4 screw or bolt, drill 4.3 mm for a close fit, 4.5 mm for a medium (normal) fit or 4.8 mm for a free fit. These are the ISO 273 fine, medium and coarse sizes.
What is the pitch of M4?
M4×0.7 has a 0.7 mm pitch (36.3 TPI equivalent), a 60° thread angle and a 4 mm major diameter.
Sources: Chart drill: the common metric coarse tapping chart. Percent values worked out from the ISO 68-1 basic profile. Clearance holes: ISO 273 (checked 25/10/2026). Values are for reference only – check your tap maker’s chart. See the disclaimer.
Spotted a mistake? Report an error.