#12 UNF tap drill size
The tap drill for #12-28 UNF is 4.6 mm, which gives about 75% of full thread. There’s no single standard chart size, so this is worked out from the thread profile for 75%.
Open in the full tap drill finder
Tap drill by thread percentage
75% is the usual workshop figure. Less thread is easier to tap; more adds little strength.
| Thread % | Ideal drill | Nearest metric drill | Nearest imperial drill |
|---|---|---|---|
| 60% | 4.779 mm 0.1882" | 4.8 mm (58%) | 3/16" 0.1875" (61%) |
| 65% | 4.72 mm 0.1858" | 4.7 mm (67%) | #13 0.1850" (67%) |
| 70% | 4.662 mm 0.1835" | 4.7 mm (67%) | #13 0.1850" (67%) |
| 75% | 4.603 mm 0.1812" | 4.6 mm (75%) | #14 0.1820" (73%) |
| 80% | 4.544 mm 0.1789" | 4.5 mm (84%) | #15 0.1800" (78%) |
About this size
UNF is the fine Unified series, common on older British and American vehicles, aircraft and instruments.
- For stainless steel, duplex and other tough materials, go to about 65% thread: a 4.7 mm drill gives 67%. For mild steel, brass and cast iron the 4.6 mm is fine.
- For a blind hole with 1.5 × D thread engagement (8.2 mm), drill about 11.9 mm deep. That leaves room for the 3–4 tapered lead threads on a second or plug tap. In steel, 1 × D engagement is usually enough; in aluminium or cast iron allow 1.5–2 × D.
Clearance holes for #12 UNF
| Fit | Drill |
|---|---|
| Close | 15/64" (5.95 mm) |
| Medium (normal) | 15/64" (5.95 mm) |
| Free (loose) | 1/4" (6.35 mm) |
Worked out with our own rule, not taken from a standards table: close = the larger of D + 4% and D + 0.2 mm, medium = the larger of D + 8% and D + 0.4 mm, free = the larger of D + 15% and D + 0.75 mm, each rounded up to the next 1/64". Check against your drawing where the fit matters.
#12 UNF thread data
| Designation | #12-28 UNF |
|---|---|
| Standard | ASME B1.1 Unified basic profile (same 60° basic form as ISO metric) |
| Pitch | 28 TPI (0.907 mm pitch) |
| Thread angle | 60° |
| Major diameter | 0.216" (5.486 mm) |
| Pitch (effective) diameter | 0.193" (4.897 mm) |
| Minor diameter, external | 0.172" (4.373 mm) |
| Minor diameter, internal | 0.177" (4.504 mm) |
| Thread depth (internal) | 0.491 mm |
Basic sizes. Real screws are slightly under and real nuts slightly over these values because of tolerance classes.
Quick calculator
Nearest alternatives
If you don’t have the right drill, these give:
- 4.5 mm drill → about 84% thread
- 4.6 mm drill → about 75% thread
- 4.7 mm drill → about 67% thread
Threads close in size (not interchangeable – the pitch and/or angle differ):
- #12 UNC – 5.49 mm major, 24 TPI (1.058 mm pitch)
- 7/32" BSF – 5.56 mm major, 28 TPI (0.907 mm pitch)
- 1BA – 5.3 mm major, 0.9 mm pitch (28.2 TPI equivalent)
- M5 – 5 mm major, 0.8 mm pitch (31.7 TPI equivalent)
- M6 – 6 mm major, 1 mm pitch (25.4 TPI equivalent)
Questions
What size drill for a #12 UNF tap?
The tap drill for #12-28 UNF is 4.6 mm, which gives about 75% of full thread. There’s no single standard chart size, so this is worked out from the thread profile for 75%.
What size clearance hole for #12 UNF?
For a #12 UNF screw or bolt, drill 15/64" for a close fit, 15/64" for a medium (normal) fit or 1/4" for a free fit. These come from our stated rule, not a standards table.
What is the pitch of #12 UNF?
#12-28 UNF has a 28 TPI (0.907 mm pitch), a 60° thread angle and a 5.486 mm major diameter.
Sources: Basic sizes per ASME B1.1. Chart drill from the common UN 75% tapping chart where one exists. Number and letter drill sizes checked 25/10/2026. Values are for reference only – check your tap maker’s chart. See the disclaimer.
Spotted a mistake? Report an error.